AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |
Back to Blog
Laser engraving peek plastic12/7/2023 ![]() ![]() of modules to be used in a project and in what way depends on the article concerned and is defined with the customer at the start of the project. Kunststoffe international,, Adding Value through Quality and Technology. High-temperature materials such as LCP, PEEK and PEI are su. Good to very good reproduction of the microstructures on cavity surfaces can be achieved with LCP, COC, easy-flowing PC, PA, POM, PBT, PEI, PPE and PSU. The Right Material is Essential Depending on the application in question, the following polymers are among the materials used for microsystems: LCP, COC, PC, PS, PPE, PMMA, PEEK, PSU, PAI, PEI, PBT, PA and POM. he filigree structures can be produced in the corresponding mould inserts. Kunststoffe international,, A Systematic Approach to Micro-Injection Moulding. These polymers are typically used when all other polymers fail, in particular when there is a need for a combination of properties such a. The generic PAEK family includes different polymers, depending on the ketone to ether ratio, such as polyetheretherketone ( PEEK), polyetherketone (PEK), polyetherketone‧etherketoneketone (PEKEKK) and polyetherketoneketone PEKK (Table 1). aerospace industry and the oil and gas market. ![]() herketones (PAEK) are used in technically challenging industry sectors, e. g. Kunststoffe international, Semi-Crystalline, and yet Thermoformable. It would have been uneconomical to use them as substitutes for metal. And high-performance poly‧mers, such as PEEK and PAI, offered consistent dimensional stability within the desired temperature window, but were ruled out for cost reasons, because the materials cost EUR 50 and more per kilogram. U-shaped polyamide sheets made of continuous fibers, which could have been overmolded, also failed to offer the necessary rigidity (calculated deviation: 3.5 mm). Kunststoffe international, Replacing Metal in the Gearbox. % solution of Bioprotect using an electrospray apparatus (fabricated by LG type: ESS AD, S/N 20073037, Athens, GA/USA) at 150 kPa pressure and allowed to dry before curing. UV curing Bioprotect as spray solutions or 100 % solids formulations to plastics either as single component to form the final antimicrobial coating with either a mercury arc or a UV LED lamp.For example, the following plastic surfaces (PS, PP, PEEK, HDPE, PVC) were spray-coated with dilute aqueous, 1 wt. Kunststoffe international, Killing Problem Microbes. They are therefore increasingly at the focus of technical series applications. Compared to high-temperature thermo‧plastics, such as polyphenylene sulfide (PPS) or polyetheretherketone ( PEEK), which combine high operating temperatures with good mechanical properties, thermoset molding compounds with similar properties are considerably less expensive. uirements and at the same time have a significantly lower density than metals (e. g. Kunststoffe international, Excellent Resistance at Reduced Weight. This is due to their high-performing properties such as light weight, high strength and. In contrast to commodity and technical polymers, polyetheretherketone ( PEEK) is a high-performance polymer located at the top of the polymer pyramid and ideally suited to extreme and demanding environments typically replacing metals. Due to its high-performing properties polyetheretherketone thermoplastic polymer is being used more and more frequently in many products. Housing used on aerospace fuel system.Kunststoffe international, Delivering Efficiency Even in Harsh Environments. Nadcap Spray Painting & Fiber Laser Etching Project Highlights To learn more about this project, see the table below or contact us directly. Finally, our highly trained staff then inspects every aspect of the finish to ensure our customer’s exacting standards are met before carefully packaging the part for return. ![]() The second coating is conductive and is applied to meet customer requirements for resistivity. We use custom cut decals to mask the part, and meticulously paint the required surfaces with a Boeing paint system. Next, we liquid honed the housing to prepare the surfaces that will be painted. We etch the ID marking, including serial number and data matrix, onto the part using our laser etching on our Ytterbium fiber laser. The customer provides the molded PEEK housing and Prime Products finishes the part according to the drawing and specifications provided. Our customer needed a company to apply the parts marking and three paint finishes using Nadcap certified processing. The housing shown here was designed by one of our customers for use in an avionics fuel system. Spray Painted PEEK Housing with Laser Etched ID Marking for the Aerospace Industry ![]()
0 Comments
Read More
Leave a Reply. |